There are still some products that have not been listed yet. For more information, please contact us. If the product model does not match the displayed picture, the actual model shall prevail. Please consult us for specific product images; We will arrange for the warehouse to take photos for confirmation. We have 76 shared warehouses worldwide, so it may take several hours to accurately respond to your message. We deeply apologize for any inconvenience caused to you. Of course, we will process your inquiry as soon as possible.

The GE IC660ELB912J is a Micro Genius network interface card designed to integrate legacy PLC or microprocessor systems with GE’s Genius I/O bus for distributed control and monitoring. The GE IC660ELB912J supports both inputs and outputs (up to thousands of I/O references) and can be configured as inputs-only or outputs-only depending on the application.

The GE IC660ELB912J is commonly used in industrial plants, turbine-control systems, and retrofitted automation lines where the GE IC660ELB912J acts as the communication gateway between the host CPU and remote Genius I/O blocks. The GE IC660ELB912J is compatible with GE Fanuc Genius bus controllers and many embedded CPU types that can read and write to its shared RAM.

Model GE IC660ELB912J

Manufacturer GE Fanuc (GE Vernova Automation)

Type Micro Genius network interface / Genius I/O daughterboard

Power supply 24 VDC (±15%), low current (typical ~150 mA)

Operating temperature Approximately −40 °C to +70 °C

Memory 512 KB RAM, 1 MB Flash (shared general-purpose RAM for host communication)

I/O mode Configurable as inputs-only, outputs-only, or mixed inputs/outputs over the Genius bus

I/O capacity Up to several thousand input/output references (e.g., on the order of 8,000 I/O “references”) via Genius I/O blocks

Bus compatibility Compatible with GE Fanuc Genius bus controller and Genius I/O blocks (Mark I/II-type systems)

Physical size Approx. 70 mm × 125 mm × 35 mm; weight about 0.2 kg

Typical use case Legacy PLC / PC-based control integrating Genius I/O; retrofit projects and turbine-control systems

Insert the GE IC660ELB912J daughterboard into the correct host slot (e.g., a PC-based or microprocessor backplane) and ensure good mechanical and electrical contact.

Connect the GE IC660ELB912J to the Genius I/O bus (Genius bus controller and Genius blocks) and verify termination and wiring.

Power the GE IC660ELB912J with 24 VDC and check LEDs to confirm normal initialization and communication with the Genius bus.

Configure the GE IC660ELB912J mode (inputs-only, outputs-only, or mixed) via host software or configuration tools, mapping the desired I/O references.

Test data exchange by reading inputs and writing outputs through the Genius I/O blocks, validating that the GE IC660ELB912J correctly forwards data between the host and remote I/O.

Always confirm the correct power-supply voltage (24 VDC ±15%) before energizing the GE IC660ELB912J and ensure the panel is properly grounded.

Handle the GE IC660ELB912J carefully to avoid ESD damage; avoid long-term exposure to moisture, dust, or vibration beyond its −40 °C to +7 dbl 70 °C rating.

When wiring the Genius bus for the GE IC660ELB912J, follow GE’s guidelines for bus length, termination, and shield grounding to maintain noise immunity and communication reliability.

Do not change the GE IC660ELB912J configuration (inputs/outputs or bus mode) while the system is operating under load; re-configure and test in a safe, de-energized mode whenever possible.

Regularly inspect the GE IC660ELB912J for abnormal LED patterns, loose connectors, or signs of overheating, especially in gas-turbine or high-temperature control-cabinet environments.

Periodically verify communication quality on the Genius bus by checking error counters or status bits connected via the GE IC660ELB912J; replace or repair the board if CRC or buserror counts increase abnormally.

Keep the surroundings of the GE IC660ELB912J free of dust and condensation and ensure the ventilation of the host cabinet is unobstructed.

If available, perform firmware or configuration backups for systems using the GE IC660ELB912J so that replacement or retrofit of the card does not require re-engineering the entire Genius-I/O mapping.

Do you provide global shipping services?

Yes. We have local distribution centers on all continents, which can quickly transport parts to any corner of the world.

2. What payment methods and currencies do you accept?

To make your purchasing process as simple as possible, we offer multiple payment methods including bank transfer, check, and PayPal. Meanwhile, we also accept most mainstream credit and debit cards, such as Visa, Mastercard, and American Express. We can accept payments in most major currencies worldwide, but we recommend using US dollars (USD), British pounds (GBP), or euros (EUR) as a priority. Payments in other currencies may incur additional fees. All transactions are securely processed by HSBC Bank and HSBC Merchant Services.

How many parts do you currently have in stock?

We have a vast inventory of thousands of new, refurbished, and outdated automation components, including products from well-known manufacturers such as ABB and Schneider. If you cannot find the required parts, please do not worry. We work closely with a global network of professional suppliers to provide you with tailored quotes even if the part is not listed on our website.

Who can I contact if I encounter any problems?

Our experienced customer service team will handle any issues after you place your order.